What wideband works with HP Tuners?
The 30-0334 X-Series OBDII Wideband Gauge is validated to work with HP Tuners VCM Suite! The X-Series Wideband AFR OBDII Gauge includes an OBDII pass-through connector and Bosch 4.9LSU sensor that can be free-air calibrated or used with the factory resistor calibration.
Do I need a wideband for HP Tuners?
The Wideband O2 air/fuel ratio UEGO gauge is a must if you want to maximize your engine’s power and safety. When tuning an engine, accurate air/fuel ratio data is critical because running with too rich of an AFR can cause a loss of power, and running a lean AFR can result in serious engine damage.
What is tuning with wideband?
In short, a wideband oxygen sensor will give you a measurement of your Air/Fuel Ratio from about 10:1 up to about 20:1 AFR allowing you to target exactly the AFR you’re after at all times. A narrowband can only tell you when it’s 14.7:1, and is therefore nearly useless for tuning.
How do I use HP Tuners nGauge?
Plug the micro SD card back into the nGauge, plug the nGauge into the OBD2 port, turn the key on and press TUNING > Load Tune. If you’ve loaded multiple custom tunes (. enc files) onto the nGauge, you can arrow left and right to select the tune you want. Press the checkbox to confirm and the tune will load.
Can you tune without a wideband?
If you plan to head to the rollers to get it setup, and want a more hands-off install, then no need for a wideband at all. The dyno operator will use their own wideband during mapping, will optimise the fuelling and ignition, and, everything being equal, it should never change once tuned.
How do I change the air fuel ratio on my HP tuner?
Changing Wide Open Throttle Air Fuel Ratio
- Location: Engine->Fuel Control (Power Enrich Tab)
- Make very small changes and use the scan tool to verify your adjustments.
- Do not rely on stock O2 sensors for accurate readings, use a wide band O2 for accurate results.
What is the EQ ratio?
The commanded equivalence. (EQ) ratio parameter (PID) is required in the generic data- stream on all passenger vehi- cles since 2008 (see the EQ to air/fuel ratio [AFR] matrix on the next page and the SAE definition in the box on page 13). An EQ of 1 equals 14.7:1 AFR.
Can you Unmarry a nGauge?
The nGauge can be “unmarried” 3 times at no cost. Returning the vehicle to stock does not unmarry the nGauge.
Who makes the nGauge tuner?
This is a brand new, “unlocked” HP Tuners nGauge, ready to be tuned using HP Tuners VCM Suite. Supports all OBD2 vehicles as a gauge and data logger. The HP Tuners nGauge is a digital gauge that connects to the vehicle’s OBD2 port, allowing the user to view live data and reprogram the ECU.
How to setup your wideband in hp tuners?
Because of popular demend we have developed a 16 page step by step instruction booklet and a screen by screen instruction video on how to setup a Wideband in Hp Tuners. The download is free. Last edited by madvette08; 03-02-2010 at 02:16 PM . I just tried your spreadsheet out and I think you have a problem with it.
Where does the ground go in hp tuners?
The Ground goes to #5 (counted from the top down, the 5th spot). If you need a picture to clarify, open your HP Tuners software, then click: HELP > SEARCH tab > type in the box “enhanced IO” > then click on the result that says “Enhanced IO – Connecting”. It shows a picture for you.
How to tune speed density using wideband O2?
Start the engine and let it come up to full operating temperature. While the engine is warming up, start the HPT Scanner, connect to the vehicle and start monitoring your data (do not log at this time). Once the engine is warm (160 °F or higher), start your drive and start Data logging. Your driving style should be very calm.
When to use a wideband air / fuel controller?
Using a wideband air/fuel controller during the tuning process allows you to monitor AFR and adjust tuning parameters to optimize them for maximum power and efficiency. AEM has a comprehensive line of highly accurate, reliable wideband air/fuel controllers that can help ensure your vehicle is optimally tuned.
