How do I go to the beginning of a file in vi?

How do I go to the beginning of a file in vi?

To go top of the file there are the following ways: press ESC

1. press 1G (Capital G)
2. press g g (small g) or 1 g g.
3. You can jump to the particular line number,e.g wanted to go 1 line number, press 1 + G.

How do you jump to the beginning of a line in vi?

You can use 0 or ^ to move to beginning of the line. And can use Shift + I to move to the beginning and switch to editing mode (Insert).

How do I get to the top of the page in Vim?

Conclusion

1. Esc + Ctrl + End – Jump end of file.
2. Hit Esc + Ctrl + Home : Jump start of file.
3. Press Esc + gg : Go to top the file.
4. Esc + G : Go to bottom of the file.
5. Esc + G + A : Go to bottom of the file and in append text mode.
6. Hit Esc + A + $ : Go to bottom of the file and end of line.

How do you go to the first line in terminal?

To navigate to the beginning of the line in use: “CTRL+a”. To navigate to the end of the line in use: “CTRL+e”.

How do I jump to a word in Vim?

Moving One Word Press w (“word”) to move the cursor to the right one word at a time. Press b (“back”) to move the cursor to the left one word at a time. Press W or B to move the cursor past the adjacent punctuation to the next or previous blank space.

How do I print only the first line?

Yes, that is one way to get the first line of output from a command. There are many other ways to capture the first line too, including sed 1q (quit after first line), sed -n 1p (only print first line, but read everything), awk ‘FNR == 1’ (only print first line, but again, read everything) etc.

What are the three modes in vi?

The three modes of vi are:

• Command mode: in this mode, you can open or create files, specify cursor position and editing command, save or quit your work . Press Esc key to return to Command mode.
• Entry mode.
• Last-Line mode: when in Command mode, type a : to go into the Last-Line mode.

How do you yank in vi?

To yank one line, position the cursor anywhere on the line and type yy . Now move the cursor to the line above where you want the yanked line to be put (copied), and type p . A copy of the yanked line will appear in a new line below the cursor. To place the yanked line in a new line above the cursor, type P .

How can I make VI start at a particular line?

To make vi start at a particular line in a file, add +line_num to the command you use to start vi. Replace line_num with the line number, for example: vi +14 file.py You can also use the ex command line to go to a line.

How to go to first line in a file in Vim?

or 1 gg. Type “gg” in command mode. This brings the cursor to the first line. If you are using gvim, you could just hit Ctrl + Home to go the first line. Similarly, Ctrl + End goes to the last line. Thanks for contributing an answer to Stack Overflow!

How do I go to the last line in a file in VI?

If you’re already in vi, you can use the goto command. To do this, press Esc, type the line number, and then press Shift-g. If you press Esc and then Shift-g without specifying a line number, it will take you to the last line in the file. You can also use the ex command line to go to a line.

Is there a short cut for going back to the beginning of a file by VI?

gg does not exist in vi, only Vim. – Matej Oct 25 ’15 at 20:27 Shift + g —> Go to the bottom of the file. Shift + GG —> Go to the top of the file. – Subhashree Pradhan May 26 ’17 at 6:29 @Subhashree Pradhan – Thank you for the insights on Vi Vs Vim.