Does a drill press require a guard?

Does a drill press require a guard?

OSHA 29 CFR 1910.212(a)(1) requires that one or more methods of drill press machine guarding shall be provided to protect the operator and other employees in the machine area from hazards such as those created by point of operation, ingoing nip points, rotating parts, flying chips and sparks.

How do you guard a drill press?

Safeguard a Drill Press Chuck Placing a shield in front of the chuck is the most popular safeguarding choice. Many options are available such as magnetic goose-neck or clamp type shields on drill presses. The problem with this type of guards is that it’s super easy just to ignore them.

What are 5 safety rules for a drill press?

Drill Press Safety Rules

  • Run drill at correct RPM for diameter of drill bit and material.
  • Always hold work in a vise or clamp to the drill table.
  • Use a correctly ground drill bit for the material being drilled.
  • Use the proper cutting fluid for the material being drilled.
  • Remove chips with a brush, never by hand.

Does OSHA require a written program for machine guarding?

OHSA machinery and machine guarding standard 29 CFR 1910 Subpart O identifies the minimum machine safeguarding requirements. The OHSA regulation does not require a written program; however, a written program helps organize and document inspection procedures to ensure proper safeguarding.

Does a drill press need to be bolted to the floor OSHA?

Drill presses are a little top heavy, but a person exercising common sense won’t have any trouble with one. No need to bolt a floor-model drill press down. It’s actually nice to be able to move it around on a mobile base to accommodate long projects once in a while.

What is ANSI B11?

The ANSI B11 standards provide a framework to identify and address machinery safety hazards and implement machine guarding through task-based risk assessment.

How does a chuck guard work?

Chuck guard are safety devices that protect workers from the excess shavings, shards, tool bits and chips of material that may fly from working machines and cause injury. They are simple curved pieces of material that are attached to the machinery by a bracket and screws.

What are the minimum requirements for protection and guards?

Guards must meet these minimum general requirements:

  • Prevent contact. The guard must prevent hands, arms, and any other part of a operator’s body from making contact with dangerous moving parts.
  • Secure.
  • Protect from falling objects.
  • Create no new hazards.
  • Create no interference.
  • Allow safe lubrication.

Does a bench grinder need to be bolted down OSHA?

Machinery, such as grinders or buffers, must be secured to a work bench or pedestal and the bench or pedestal, in turn, must be secured to the floor to prevent walking or moving.

What are the safety guards on a drill press?

Safety Guards for Drill Presses Shown on Drill Press (Drill Press and Bit Not Included) Keep your fingers and hands protected from your drill bit, drill chuck, and flying chips. This guard retracts as the drill penetrates your material, lowers when the spindle is raised, and flips out of the way for quick bit changes.

How big is a Delta drill press guard?

The Delta Drill Press Guard is a simple solution to adding a safety feature to your drill press to provide you a safer working environment. Designed to fit any drill press with a column diameter ranging from 1-1/2 in. to 3-11/16 in., this guard is quick and easy to install.

Is there a way to change drill chucks?

For changing chucks or drill bits, the 2- or 3-tier section can be swung forward and upward out of the way. Also available are drill press shields with a side hinge that swing to the left side. For best safety practices, electrically-interlocked drill press shields are also available. Several sizes of drill chuck keys are available.

How big does a drill press shield need to be?

These cast-aluminum drill press shields are furnished with a standard 1 3/4-inch bore. The user can bore this shield to a size of up to 3 1/2-inches for attaching to the quill of a drilling machine. This drill press shield is available in 2-tier or 3-tier models which provides 3- to 6-inches travel of the drill press.

About the Author

You may also like these