How do you measure a jeep drive shaft?
2:28Suggested clip 70 secondsHow to Measure Driveshaft / How to measure your Jeep wrangler …YouTubeStart of suggested clipEnd of suggested clip
What size drive shaft do I need?
If your driveshaft is of this type, measure the distance from the centerline of the front U-joint to the centerline of the rear U-joint. Tip: Ahead of time, look at the tape measure you are using and identify how 1/16th of an inch is marked. This will be the degree of accuracy you need for driveshaft length.
What is a slip yoke eliminator YJ?
What is a Slip Yoke Eliminator or an SYE? A slip yoke eliminator (SYE) eliminates the slip yoke from your drivetrain, turning it into a fixed yoke. A longer driveshaft means you’ll have a flatter drivetrain angle, reducing vibrations and wear on drivetrain parts if your Jeep has an agressive lift installed.
Is my Jeep a YJ?
The easiest, and quickest, way to know if your Wrangler is a YJ is to look at the grille. Wrangler YJs were the first Jeep to offer square headlights instead of the traditional round ones.
What does YJ stand for on a Jeep?
Yuppie Jeep
What years did jeep make the YJ?
The Jeep Wrangler YJ was the first generation of Jeep Wrangler four-wheel drive small off-road vehicles, rebadging and succeeding Jeep’s CJ series, produced from 19. The first Wrangler (internally “YJ”) was launched in 1986 and ran through 1995.
What is the best Jeep ever made?
The 5 Best Jeeps Ever MadeJeep CJ-2A. The CJ-2A deserves its place on a list of the best Jeep vehicles ever made because it was the first one available to civilians. Jeep CJ-8 Scrambler. The Jeep CJ-8 Scrambler was one of the more eye-catching vehicles ever produced. Jeep Grand Cherokee. Jeep J10. Jeep YJ.
What is the difference between a TJ and YJ Jeep?
A YJ came with a Dana 30 front axle and a Dana 35 on the rear, while the TJ came with a Dana 30 front axle and a Dana 35c in the rear. The TJ Rubicon came with the option of having Dana 44 front and rear axles. One of the more significant differences between the YJ and the TJ has to do with the frame and suspension.
Is the 2.5 jeep engine good?
The 2.5 is just as reliable as the 4.0. It’s the same motor minus 2 cylinders as was already mentioned. It just kind of sucks because it has no balls. The 2.5 is just as reliable as the 4.0, the 4.0 is actually based on the 2.5.
Who makes the 2.5 engine for Jeep?
American Motors Corporation
Is the 4 cylinder Jeep motor good?
Now, the four-cylinder. It’s the best Wrangler powerplant yet. Yes, it’s down 15 horsepower on the standard V-6 and it costs $1,000 more. But it nets significantly better mileage (up to an extra 4 mpg on the EPA combined cycle) and is temperamentally better suited to Wrangler duty.
Are Jeep 4.0 engines reliable?
The Jeep 4.0L I-6 is extremely reliable. If you Googled that engine, or went onto various Jeep forums, you’d be hard pressed to find one that died after any number of miles – providing it was properly serviced during its life.
What year Jeep 4.0 is the best?
#10 – Jeep 4.0L Straight-Six This little engine that could is best known for reliably powering a variety of Jeep utility vehicles from 1986 through its phase out in 2006.
How long do Jeep 4.0 engines last?
Provided that it really does get taken care of and driven normally, It is safe to say around 150000, but you can expect more than that in MOST cases. I personally have a 93 YJ with the 4.0 in it and its kickin along great at 135000 miles.
How long will a jeep inline 6 last?
Well kept, you can go upwards of 300K on them. Based on my experience, about 175-200k miles before it needs a rebuild. Based on my experience, about 175-200k miles before it needs a rebuild.
What year did jeep stop using the inline 6?
2006
Why is the Jeep 4.0 so good?
Made of long lasting materials, the bore and stroke is over square like most engines. The oversquare engine is quite good at low rpm, most efficient in the middle rpm range and has good high-rpm performance (torque and horsepower).
How long do inline 6 engines last?
Originally Answered: How many miles should the BMW inline 6 cylinder engine be expected to go before needing a rebuild? They are designed for 300,000 km under “normal condition”. Drive them at low rpm and long distance and they usually outlive the car they are in.
Is inline 6 better than v8?
The I6 motor that the truck has in game has a bigger displacement per-cylinder than the V8. At higher rpm the v8 should make more horsepower(horsepower is just a funtion of torque also) but since it has more cylinders it performs better at higher rpm(not always the case).
Why are straight 6 engines so good?
Straight six advantages With no cylinder offset, manufacturing costs are low and there is no need for separate heads or valvetrains like in a V-configuration. Instead of using double the amount of smaller camshafts, a DOHC I6 can simply use two longer camshafts to open and close its valves.
